Gutter repair in Tampa
Leaks, sags, standing water and loose downspouts, fixed at the cause. If a run isn't worth saving, we'll say so and explain why.
- Free, no-obligation quotes
- Measured on site
- Written scope before booking
Repairs
Most gutter problems start small
A gutter that drips at one corner, or sags a couple of inches along one wall, is usually a fixable problem. Left alone, it rarely stays small. The drip soaks the fascia, the wood softens, the hangers lose their grip, and the sag gets worse.
Gutter repair is about finding why the water isn't going where it should and fixing that, not just smearing sealant on the wet spot. A leak at a joint might be old sealant. It might also be a gutter pitched the wrong way, so water sits against that joint all day. Sealing it without fixing the pitch just buys a few months.
We repair aluminum, seamless and sectional systems, including gutters we didn't install. If you'd like us to look at yours, give us a call on (813) 694-8119 and a few photos if you have them.
Call about a repair if you see
- Water dripping from a corner, seam or end cap
- A section leaning out from the roof edge
- Water standing in the gutter long after rain stops
- Overflow at one spot while the rest drains fine
- A downspout hanging loose or detached at the elbow
- Peeling paint or dark stains on the fascia board
What we fix
Gutter repairs we handle
The common failures on Tampa homes, and what the fix usually involves.
Leaking seams and end caps
Old sealant cracks in the heat and pulls away from the metal. We clean the joint back to bare aluminum, reseal it, and re-crimp or re-fasten end caps that have worked loose.
Leaking miters
Corners carry water from two runs and take the most stress. A dripping miter often needs to be taken apart, resealed and refastened rather than just caulked over.
Sagging or pulled-away runs
Usually a failed hanger, a spike that has backed out, or fascia that can't hold a screw anymore. We add or replace hangers and fix the wood if it's soft.
Re-pitching
If water pools mid-run or flows away from the outlet, the gutter needs to be re-hung with proper fall. Around 1/4" per 10 ft is a common rule of thumb; the right number depends on the run.
Loose or crushed downspouts
Straps come loose, elbows get knocked off by mowers, and bottoms get crushed. We reattach, replace damaged pieces, and make sure the discharge points away from the house.
Clogged outlets
Oak leaves, pine needles and Spanish moss pack into the outlet and the top elbow. We clear them and check whether the outlet is sized right for the run.
What rotten fascia looks like from the ground: paint blistering or peeling right behind the gutter, a gutter that tilts outward, dark streaks under the roof edge, or soffit panels sagging near a corner.
If you push on the fascia with a screwdriver from a ladder and it sinks in, the wood is soft.
Behind the gutter
Fascia repair, done before the gutter goes back up
The gutter hangs on the fascia board at the roof edge. On many Tampa homes that board is wood, sometimes wrapped in aluminum. When water gets behind the gutter from a leak, an overflow, or a missing drip edge, the wood stays wet and starts to rot. The gutter's fasteners then have nothing solid to grip.
That's why a sag is often a fascia problem wearing a gutter costume. Putting new screws into rotted wood holds for a few storms at best. We take the gutter down along the damaged section, cut out the soft fascia, replace it, and rehang the gutter on sound material.
Where there's aluminum wrap over the wood, the rot can be hidden until the wrap is pulled back. We'll show you what we find before doing work beyond the written scope.
After a blow
Storm damage to gutters
Tampa is hurricane-prone, and even ordinary summer squalls bring branches down and strong gusts off the water. After a storm, walk the house once it's safe and look for these.
- Gutters bent or kinked where a limb landed
- Sections pulled partly off the fascia by wind
- Downspouts torn off at the top elbow
- Debris piled in the trough and blocking outlets
- Dents that now hold water
- Gaps between the gutter and the drip edge
A bent section can sometimes be straightened and rehung. A kinked or torn one is usually cut out and replaced with new gutter joined in. If you're filing an insurance claim, take photos before anything is moved. Before storm season, clearing debris and checking that every hanger is tight is the best prep you can do.
The visit
How a repair visit works
Tell us what's happening
Where it leaks, where it sags, and when it's worst. Photos taken during rain are the most useful thing you can send.
Inspect the whole run
We check the pitch, the joints, the hangers, the outlets and the fascia on the run in question and the ones next to it, because problems often share a cause.
Written scope
You get a list of what we'd repair and what it covers. If replacement makes more sense, we'll tell you and explain why.
Repair and test
We make the repairs, then run water through the system to confirm it drains to the outlet and out the downspout.
Repair or replace
When a repair isn't worth it
We'd rather fix a gutter than sell you a new one when a fix will last. But some systems are past the point where repairs make sense. Signs a replacement is the smarter spend:
- Leaks at joints along most of the system, not just one or two
- Rust holes in old steel gutters
- Undersized gutters that overflow every storm even when clean
- Fascia rot in several places around the house
- Repeated repairs on the same runs
There's a longer checklist in signs your gutters need replacing. In those cases, spending on repairs mostly delays the inevitable. Our gutter replacement service covers tearing off the old system, fixing the roof edge, and putting up new seamless runs.
What affects a repair quote
- How many spots need work, and where they are
- Whether fascia needs replacing behind the gutter
- Whether runs need to come down to be re-pitched
- Replacement parts: hangers, end caps, elbows, sections
- Height and access to the damaged area
We give you the scope in writing before booking.
Gutter repair questions
Can you repair gutters another company installed?
Yes. We work on aluminum gutters of all kinds, seamless and sectional, whoever put them up.
Why does my gutter overflow in only one spot?
Usually a clogged outlet, a low spot in the pitch, or a valley dumping more water into that corner than the gutter can carry. Sometimes the fix is a cleaner outlet, sometimes an extra downspout. We explain the usual causes in why gutters overflow in storms. Adding downspouts is often the answer for corners that overflow in heavy rain.
Is sealant enough to fix a leaking gutter joint?
Only if the joint is otherwise sound and the gutter drains properly. If water sits against the joint because of poor pitch, or the joint has pulled apart, sealant alone won't last.
Will gutter guards stop repairs from being needed?
Guards cut down on clogs, which reduces overflow and standing water. They don't fix bad pitch, failed joints or rotten fascia. If debris is the main cause of your problems, ask about gutter guards once the repairs are done.
More gutter services
Gutter repairs around Tampa
We handle repairs throughout Tampa and in communities like Carrollwood, Brandon, Temple Terrace and Town 'n' Country. All service areas.
Free quote ยท Call us
Get a gutter repair quote
Talk to us about the house and what the water is doing. We'll arrange a time to measure and give you a clear written quote. There's no charge and no obligation.
Call (813) 694-8119620 E Twiggs St, Tampa, FL 33602
What happens when you call
- Tell us what's happeningOverflow, leaks, sagging, or a house with no gutters yet.
- We come out and measureRoof edge, fascia, trees and where the water needs to go.
- You get a written quoteSizes, color, downspouts and any repairs, before anything is booked.